manualshive.com logo in svg

TRACE ELLIOT ACOUSTIC P.A, Operating Instructions Manual

Share
Download
TRACE ELLIOT ACOUSTIC P.A Operating Instructions Manual Download Page 15

DPS Effects Level Slider
The DPS Effect Level slider controls the stereo output level from the internal effects
processor and as such acts as an effects master level control for setting the required level
of effects in the mix.
The DPS/Aux1 controls on each channel set the level of signal to the input of the effects
processor allowing each channel to be adjusted for its own level of effects. The overall
combined effects level from the output of the effects processor is set with the above
control.

Reverb Footswitch
A reverb footswitch jack socket is provided at the top of the master section to allow
external muting of the internal effects. This requires an external closed contact to mute the
internal effects.

Aux Sends
The two Aux Send signal output jack sockets are at the top left of the master section and
each has its own output master level control to adjust the signal to suit a wide range of
external effects processor units.

Aux1/Aux2 Master Level Control
The level of effects required for each individual channel is set with each specific channels
own Aux 1 and Aux 2 control. These combine together to provide the signal sent to the
external effects unit from the Aux 1 and Aux 2 jack sockets. The overall level of signal sent
to the external effects unit is adjusted using the Aux 1 and Aux 2 Master level controls
located directly below these controls.

Master Left and Right Faders
The Master Faders are located close together as normally they will be increased and
decreased together to adjust the stereo output from the mixer.
The Master Faders control the signal level to the LEFT and RIGHT STEREO MASTER
OUTPUT jack sockets as well as the signal level to the internal power amplifiers via the
POWER AMP LEVEL control. They also adjust the level of signal sent to the SUB OUT jack
socket via the SUB LEVEL control.

Power Amp Level Control
The POWER AMP LEVEL control is used to set the overall level of the internal power
amplifiers in conjunction with the Master Faders. This is useful to balance the system
when you are using an additional power amplifier and speakers driven from the Left and
Right STEREO MASTER OUTPUT jack sockets.
As a general guide it is best to set this control at about half and then use the Master
Faders to adjust the overall performance volume.

16

Summary of Contents for ACOUSTIC P.A























Reviews:

No comments

Brands by name

Popular brands

Load more brands