TPS MC-83 Handbook Download Page 1

Congratulations !

 

You have purchased the latest in Handheld Relative Humidity and 
Temperature instrumentation. We trust that your new 

MC-83

 Relative 

Humidity-Temperature meter will give you many years of reliable service. 

The 

MC-83

 is a breeze to operate. This manual has been designed to 

help you get started, and also contains some handy tips. If at any stage 
you require assistance, please contact either your local TPS 
representative or the TPS factory in Brisbane. 

The manual is divided into the following sections: 

1. 

Table of Contents

 

Each major section of the handbook is clearly listed. Sub-sections have 
also been included to enable you to find the information you need at a 
glance. 

2. 

Introduction

 

The introduction has a diagram and explanation of the display and 
controls of the 

MC-83

. It also contains a full listing of all of the items that 

you should have received with your 

MC-83

. Please take the time to read 

this section, as it explains some of items that are mentioned in 
subsequent sections. 

3. 

Main Section

 

The main section of the handbook provides full details of the 

MC-83

including operating modes, troubleshooting, specifications, and warranty 
terms.

 

MC-83 Humidity

 

& Temperature Meter

 

Version : 2.01 
Date : 09/04/2003 
 Author : MS

 

Summary of Contents for MC-83

















Reviews: