background image

 

Instrument Overview

 

Power Key 

Record Key 

Hold Key 

°C or °F key 

Recall Key 

Battery Compartment 

Dual LCD 

RS232 Output 

Sensors 

Remote 
Vane Probe 

Unit Key 

Operating Instructions 

 
1. 

Select the Hot probe or Vane probe for location of measurement.

 

2. 

Connect the selected probe to the meter.

 

3. 

Push ON button to turn meter on.

 

4. 

Push HOT WIRE button or VANE button as per a selected probe.

 

5. 

Pressing the 'C/'F button will toggle between 'C and 'F.

 

6. 

Push UNIT button to select the desired display units of the air       
velocity.

 

7.  The user can scroll through 5 units: - m/s, km/s, ft/min, knots,        

mile/h. 

8.  If you selected a hot probe, pull down the sensor cover of the probe 

(so that air velocity sensor can be seen) and position the probe at 
desired location of measurement.  The Probe should be positioned 
so that a white spot will face the winds. In case the place is too far 
and the antenna should be pulled long, do not hold the probe sensor, 
but hold the antenna. 

Zero Key 

Hot/Vane Key 

Remote Hot 
Wire Probe 

 

9.  Read the velocity and temperature on the LCD. 
10. It will take several minutes until the readings get stable after the 

probe is positioned. 

11.  Press "HOLD" button to freeze the display after taking a measure-

ment is finished.  

12. "DH" will be displayed on the LCD. 
13. Press "HOLD" button again to return to normal operation. 

 

Battery should be replaced when "LBT" is displayed at the top left of the screen. 

 

Volume Measurements 

 
To determine CFM (cubic feet per minute) in a duct, the area of the duct 
must first be measured (use the equations below). Then multiply an air 
velocity measurement by the area measurement to obtain CFM. 

 

 

 
 
 
 
 

 

 

 
 
 
 

 
Recording Data 

 
If you want to record the reading changes, press "REC" button when the 
reading gets stable. Once activated the meter will begin recording.   
 

Height (H) 

Width (W) 

Area (A) =  Height (H) X Width (W) 

Area Equation for Square Ducts:

 

Radius (R) 

Area (A) =  

π

 

X R

2  

 

Where 

π

 

3.14

 

           R

2

  = (Radius x Radius)

 

Area Equation for Round Ducts:

 

CFM (ft

3

/min) = Air Velocity (ft/min)  X Area (

in square Inches

144 

Summary of Contents for 575









Reviews: