TPI 296 Instruction Manual Download Page 7

Page: 7 / 32

INTERNATIONAL SYMBOLS

CAUTION: RISK OF ELECTRIC SHOCK

AC (ALTERNATION CURRENT)

DC (DIRECT CURRENT)

REFER TO INSTRUCTION MANUAL

GROUND
DOUBLE INSULATION

EITHER DC OR AC

C. TECHNICAL DATA

1. Features and Benefits

Agency

UL Listed to U.S. and Canadian Safety
Standards. Meets CE and IEC 1010.

True RMS

Needed to accurately measure non-sinu-
soidal AC voltage and current waveforms
found on many controls and circuits.

HDR Mode

Determines if a signal is clean or distorted.
Displays the harmonic distortion ratio on
ACV and ACA at line voltage and 60 Hz.

4000 Count

Improves the resolution on all functions
and ranges.

Data Hold

Maintains the reading on the display for
hard to reads areas.

Peak Mode

Measure the inrush current of motors,
relays and solenoids.

Trim Mode

Averages the readings for more stable out-
put on LCD.

Record Mode

Records Min/Max and Average value of the
function being measured.

Sleep Mode

Automatically powers down after 10
minutes of inactivity.

Frequency

Measures the frequency of the current
being measured.

Dual Display

When measuring frequency, the bar graph
indicates the current level.

Bar Graph

Shows rapidly changing input signals
that the normal display will not.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for 296

































Search results

Summary of Contents for 296

Reviews:

Related manuals for 296

Brands by name

Popular brands

TPI 296, Instruction Manual

Search results

Summary of Contents for 296

Reviews:

Related manuals for 296

Brands by name

Popular brands