background image

I

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. 

 is a registered trademark 

of  TP-LINK  TECHNOLOGIES  CO.,  LTD.  Other  brands  and  product  names  are  trademarks  of  their 
respective holders.

No  part  of  the  specifications  may  be  reproduced  in  any  form  or  by  any  means  or  used  to  make 
any derivative such as translation, transformation, or adaptation without permission from TP-LINK 
TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful interference in which case 
the user will be required to correct the interference at his own expense.

This  device  complies  with  part  15  of  the  FCC  Rules.  Operation  is  subject  to  the  following  two 
conditions:

This device may not cause harmful interference.

11 

This  device  must  accept  any  interference  received,  including  interference  that  may  cause 

21 

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could 
void the user’s authority to operate the equipment.

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in 
which case the user may be required to take adequate measures.

Copyright & Trademarks

Summary of Contents for TL-SL2428





























Reviews: