background image

 

FCC STATEMENT 

 

This equipment has been tested and found to comply with the limits 

for a Class A digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in a commercial 

environment. This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with 

the instruction manual, may cause harmful interference to radio 

communications. Operation of this equipment in a residential area is 

likely to cause harmful interference in which case the user will be 

required to correct the interference at his own expense. 

This device complies with part 15 of the FCC Rules. Operation is 

subject to the following two conditions: 

1)  This device may not cause harmful interference. 
2)  This device must accept any interference received, including 

interference that may cause undesired operation. 

Any changes or modifications not expressly approved by the party 

responsible for compliance could void the user’s authority to operate 

the equipment. 

CE Mark Warning 

 

This is a class A product. In a domestic environment, this product 

may cause radio interference, in which case the user may be 

required to take adequate measures. 

 

Summary of Contents for MC110CS





















Reviews: