background image

TD-8816B

ADSL2/2+ Ethernet Modem User Guide 

 

 

31

 

Figure 4-26 

¾

 

ACL: 

If 

Activated

, the IP addresses which are contained in the Access Control List can 

access to the Router. If 

Deactivated

, all IP addresses can access to the Router. 

¾

 

ACL Rule Index:

 Select the ACL rule index for the entry.   

¾

 

Active:

 Enable the ACL rule. 

¾

 

Secure IP Address:

 Select the IP addresses which are permitted to access to the Router 

remotely. With the default IP 0.0.0.0, any client would be allowed to remotely access the 
ADSL Router. 

¾

 

Application:

 Select the application for the ACL rule, and then you can access the Router 

through it. 

¾

 

Interface:

 Select the interface for access: LAN, WAN or Both. 

¾

 

Access Control of Listing:

 This displays the information about the ACL Rules. 

4.5.2  Filter 

Choose “

Access Management

Filter

”, you can see the Filter screen (the default is IP/MAC 

Filter screen shown in ). The filtering feature includes IP/MAC Filter, Application Filter, URL Filter. 

The feature makes it possible for administrators to control user's access to the Internet, protect 

the networks.   

4.5.2.1.  IP Filter 

Select 

IP/Mac Filter

 as the Filter type, and select 

IP

 as the Rule type (shown in Figure 4-27), then 

you can configure the filter rules based on IP address. The filtering includes 

Outgoing 

and

 

Incoming

, the detailed descriptions are provided below.

 

Summary of Contents for ADSL2/2+























































Reviews: