Toyota VENZA PT949-08210 Manual Download Page 10

Page: 10 / 11

TOYOTA

VENZA

2021 - DASHCAM (Digital Video Recorder)

Procedure

Page 10 of 11 pages

Issue: D 4/14/2021

DIO

NOTE: Do not block access to the indicated
clip hole or else roof console may not attach
correctly.

(i)

Clip off extra wire tie length.

11.

Reassemble the console

(a)

Reconnect roof console connector.

(b)

Reinstall roof console (Fig. 11-1).

(1)

Engage front hooks of the roof
console into the headliner opening.
Tilt up and push upward to engage
the clips into the roof.

NOTE: Make sure to align clip holes before
pushing up to avoid damage to clips.

(c)

Place the Quick Start Guide in the Glove
Box.

12.

Reconnect Battery.

(a)

Reconnect the negative battery cable
(Fig. 12-1).

Torque:

5.4 N•m (48 in•lbsf)

CAUTION:

Do not

touch the positive terminal

with any tool

13.

Reinstall Battery Cover and Remove

Protective Covering

(a)

Reinstall battery service hole cover in step 1c

(b)

Remove and discard vehicle protective
covering

Fig. 12-1

10mm socket & torque wrench

Fig. 11-1

Summary of Contents for VENZA PT949-08210












Search results

Summary of Contents for VENZA PT949-08210

Reviews:

Related manuals for VENZA PT949-08210

Brands by name

Popular brands

Toyota VENZA PT949-08210, Manual

Search results

Summary of Contents for VENZA PT949-08210

Reviews:

Related manuals for VENZA PT949-08210

Brands by name

Popular brands