background image

TOYOTA 

VENZA 

2021 -   DASHCAM (Digital Video Recorder) 

Preparation 

 

Page 1 of 11 pages 

Issue: D  4/14/2021 

DIO 

Part Number:  PT949-08210 (Dash Cam) 

 

PT949-48210 (Y-Harness)  

Kit Contents 

Item #  Quantity Reqd.  Description 

Dashcam Main Unit 

Window Mounting Plate 

Foam Tape 

Cable Ties 

Quick Start Guide 

Y-Harness 

Hardware Bag Contents 

Item #  Quantity Reqd.  Description  

 

 

 

 

 

 

Additional Items Required For Installation 

Item #  Quantity Reqd.  Description 

 

 

 

 

Conflicts 

None 

Recommended Tools 

Personal & Vehicle 

Protection 

Notes 

Seat protection 

 

Dash protection 

 

 

 

Special Tools 

Notes 

 

 

Installation Tools 

Notes 

Panel Tool 

 

Socket Wrench 

With 10mm socket 

Torque Wrench 

With 10mm socket 

Special Chemicals 

Notes 

VDC approved cleaner 

To clean windshield 

 

 

General Applicability 

Applicable to XLE, Limited models 

Recommended Sequence of Application 

Item #  Accessory 

Dashcam (PT949-08210) 

Y-Harness (PT949-48210) 

 

 

 

*Mandatory 

Vehicle Service Parts

 

(may be required for reassembly) 

Item #  Quantity Reqd.  Description 

 

 

 

 

 

 

 

 

 

Legend 

 

 

STOP:

 Damage to the vehicle may occur.  Do not 

proceed until process has been complied with. 

OPERATOR SAFETY:

 Use caution to avoid risk of 

injury. 

CAUTION:

 A process that must be carefully observed 

in order to reduce the risk of damage to the 

accessory/vehicle and to ensure a quality installation. 

TOOLS & EQUIPMENT:

 Used in Figures calls out the 

specific tools and equipment recommended for this 

process. 

REVISION MARK:

 This mark highlights a change in 

installation with respect to previous issue. 

 

SAFETY TORQUE:

 This mark indicates that torque is 

related to safety. 

Summary of Contents for VENZA PT949-08210












Reviews: