manualshive.com logo in svg

Toyota PT545-00082, Installation Instructions Manual

Share
Download
Toyota PT545-00082 Installation Instructions Manual Download Page 9

TOYOTA PRIUS  2008 

- 

 

INTERFACE KIT FOR IPOD 

Procedure 

 

 

Page 9 of 13 pages 

DIO

Issue: B       9/08/08

 

 
(c)

 

If the 12 pin connector is already pre-wired to 

the head unit. 

(1)

 

Remove the pre-wired 12 pin connector 

from the head unit. 

(2)

 

If applicable, plug the pre-wired 12 pin 

connector into the connector of the AVC-

LAN cable. (Fig. 4-2 & 4-3) 

 

 

(3)

 

Wrap the connectors with adhesive 

protective foam to secure. (Fig.4-4) 

(4)

 

Reconnect the factory harness and antenna 

cable. 

 

 

(d)

 

If the 12 pin connector is not pre-wired to the 

head unit. 

(1)

 

Wrap the unused connector of the AVC-

LAN cable in adhesive protective foam.  

(Fig. 4-5) 

(2)

 

Reconnect the factory harness and antenna 

cable. 

 

(e)

 

Plug the connector of the AVC-LAN cable 

into the head unit. (Fig. 4-6) 

(f)

 

Reinstall head unit. 

 

 

 

Vehicle’s 12 Pin 
Connector 

Connector of 
AVC-LAN Cable 

Fig. 4-3 

Adhesive 
Protective Foam 

Fig. 4-4 

Fig. 4-6 

AVC-LAN Cable 

Adhesive Protective 
Foam 

Fig. 4-5 

Summary of Contents for PT545-00082














Reviews:

No comments

Brands by name

Popular brands

Load more brands