Toyota Lexus IS300 Manual Download Page 242 | Manualshive

Page: 242 / 389

background image

STARTING AND DRIVING

229

HOW TO START THE ENGINE

Before cranking

1. Apply the parking brake firmly.

2. Turn off unnecessary lights and accessories.

3. Manual transmission: Press the clutch pedal to the floor
and shift the transmission into neutral. Hold the clutch pedal
to the floor until the engine is started. A starter safety device
will prevent the starter from operating if the clutch pedal is not
fully depressed.
Automatic transmission: Put the selector lever in ”P”. If you
need to restart the engine while the vehicle is moving, put the
selector lever in ”N”. A starter safety device will prevent the
starter from operating if the selector lever is in any drive
position.

4. For automatic transmission only:Depress the brake
pedal and hold it to the floor until driving off.

Starting the engine

Before starting the engine, be sure to follow the instructions in
”Before cranking”.

Normal starting procedure

The multiport fuel injection system/sequential multiport fuel
injection system in your engine automatically controls the
proper air–fuel mixture for starting. You can start a cold or hot
engine as follows:

1. With your foot off the accelerator pedal, crank the engine by
turning the key to ”START”. Release it when the engine starts.

2. After the engine runs for about 10 seconds, you are ready
to drive.

If the weather is below freezing, let the engine warm up for a
few minutes before driving. Do not leave the vehicle while the
engine is warming up.

If the engine stalls ...

Simply restart it , using the correct procedure given in normal
starting.

If the engine will not start

See ”If your vehicle will not start” on page 267.

NOTICE

Do not crank for more than 30 seconds at a time. This
may overheat the starter and wiring systems.

Do not race a cold engine.

If the engine becomes difficult to start or stalls
frequently, have the engine checked immediately.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
240
241
242
243
244
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: UnderCover Pages: 16

Brand: Warrior Products Pages: 2

Yamaha Rhino 660

Brand: Yamaha Pages: 3

Brand: GMC Pages: 20

Brand: Ultra-tow Pages: 14

Brand: Mercedes-Benz Pages: 121

Brand: Menabo Pages: 8

Brand: Camtree Pages: 5

Brand: Metra Electronics Pages: 2

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Brand: Ironton Pages: 7

Brand: SuperATV Pages: 7

Brand: Kuda Pages: 2

Brand: Ford Pages: 458

Brand: Volvo Pages: 123

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

Brand: Kleinn Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands