Toyota ESM21 Instruction Manual Download Page 47 | Manualshive

Page: 47 / 55

background image

46

Maintenance

V. Maintenance

1. Feed dog and hook maintenance

If the sewing machine makes a loud noise or rotates slowly,
the oil could have run out, or there could be thread waste or
dust in the hook or feed dog. Clean and oil the hook and feed
dog.

Before cleaning the hook, remove the power plug from the outlet.

Not doing so could cause an injury.

Attention

Do not use detergent, bleach, benzine, or thinner chemical cloths.
Doing so could cause discoloration or cracking.

Release the presser foot, and use the needle plate
screw driver to release the needle plate.

Remove thread waste and dust with a brush

(Optional accessory).

Remove the bobbin case.

«
...
45
46
47
48
49
...
»

Summary of Contents for ESM21
























































Reviews:

No comments

Related manuals for ESM21

Brand: Baby Lock Pages: 364

Brand: Necchi Pages: 122

KX-TG2248S - 2.4 GHz Digital Cordless Phone Answering...

Brand: Panasonic Pages: 35

Brand: Tornado Pages: 23

Brand: Kärcher Pages: 28

Brand: Sagem Pages: 2

Brand: Olivetti Pages: 64

Brand: Oki Pages: 137

Brand: Philips Pages: 2

LBH-1790A Series

Brand: JUKI Pages: 5

Brand: JUKI Pages: 33

Brand: SunStar Pages: 41

Brand: Edic Pages: 12

Brand: Rexel Pages: 48

Brand: Chicago Pneumatic Pages: 32

Voice Fax Gateway

Brand: Teltonika Pages: 34

DecoHome DGSTEPPER

Brand: Deco Gear Pages: 36

Brand: Nagel Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands