Toyota Corolla 2008 Owner'S Manual Download Page 8 | Manualshive

Page: 8 / 310

background image

’08 Corolla_U (L/O 0706)

182

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

The tandem master cylinder brake system
is a hydraulic system with two separate
sub−systems. If either sub−system should
fail, the other will still work. However, the
pedal will be harder to press, and your
stopping distance will increase. Also, the
brake system warning light may come on.

CAUTION

Do not drive your vehicle with only a
single brake system. Have your
brakes fixed immediately.

BRAKE BOOSTER

The brake booster uses engine vacuum to
power−assist the brakes. If the engine
should quit while you are driving, you can
bring the vehicle to a stop with normal
pedal pressure. There is enough reserved
vacuum for one or two stops—but no
more!

CAUTION

Do not pump the brake pedal if the
engine stalls. Each push on the
pedal uses up your reserved vacu-
um.

Even if the power assist is com-
pletely lost, the brakes will still
work. But you will have to push the
pedal hard, much harder than nor-
mal. And your braking distance will
increase.

ANTI−LOCK BRAKE SYSTEM (with
“ABS” warning light)

The anti−lock brake system is designed
to help prevent lock−up of the wheels
during a sudden braking or braking on
slippery road surfaces. This assists in
providing directional stability and steer-
ing performance of the vehicle under
these circumstances.

Effective way to press the ABS brake
pedal: When the anti−lock brake system
function is in action, you may feel the
brake pedal pulsating and hear a noise.
In this situation, to let the anti−lock
brake system work for you, just hold the
brake pedal down more firmly. Do not
pump the brake in a panic stop. This
will result in reduced braking performan-
ce.

The anti−lock brake system becomes op-
erative after the vehicle has accelerated
to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the
vehicle decelerates to a speed below
approximately 5 km/h (3 mph).

Depressing the brake pedal on slippery
road surfaces such as on a manhole cov-
er, a steel plate at a construction site,
joints in a bridge, etc. on a rainy day
tends to activate the anti−lock brake sys-
tem.

Brake system

«
...
6
7
8
9
10
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: AC Schnitzer Pages: 16

Brand: Zavoli Pages: 26

Brand: Xblitz Pages: 16

Brand: Wagan Pages: 8

Brand: Thermo King Pages: 2

2008 MX-5 Miata

Brand: Mazda Pages: 400

Brand: StowAway 2 Pages: 2

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

Brand: RAM Pages: 330

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

Brand: Thule Pages: 8

Brand: Grillo Pages: 71

Brand: TATA Motors Pages: 232

Brand: Prorack Pages: 14

Brand: Mercedes-Benz Pages: 24

Brand: Yakima Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands