Toyota Corolla 2008 Owner'S Manual Download Page 69 | Manualshive

Page: 69 / 310

background image

’08 Corolla_U (L/O 0706)

243

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

2. Use a good quality polish and wax. If

the finish has become extremely weath-
ered, use a car−cleaning polish, fol-
lowed by a separate wax. Carefully fol-
low the manufacturer’s instructions and
precautions. Be sure to polish and wax
the chrome trim as well as the paint.

Windshield washer nozzles: Make sure
that the nozzles do not become blocked
when waxing. If a nozzle becomes
blocked, contact your Toyota dealer to
have the vehicle serviced.

NOTICE

If a nozzle becomes blocked, do not
try to clear it with a pin or other
object. The nozzle will be damaged.

Exterior lights: Do not apply wax on the
surfaces of the lights. Wax may cause
damage to the lenses. If you accidentally
put wax on the light surfaces, wipe or
wash it off.

3. Wax the vehicle again when water

does not bead but remains on the sur-
face in large patches.

CAUTION

Vehicles with side airbags and cur-
tain shield airbags:

Be careful not to splash water or
spill liquid on the floor. This may
prevent the side airbags from acti-
vating correctly, resulting in serious
injury.

Do not wash the vehicle floor with
water, or allow water to get onto
the floor when cleaning the vehicle
interior or exterior. Water may get
into audio components or other
electrical components above or un-
der the floor carpet (or mat) and
cause a malfunction; and it may
cause body corrosion.

Vinyl interior

The vinyl upholstery may be easily
cleaned with a mild soap or detergent
and water.

First vacuum over the upholstery to re-
move loose dirt. Then, using a sponge or
soft cloth, apply the soap solution to the
vinyl. After allowing it to soak in for a few
minutes to loosen the dirt, remove the dirt
and wipe off the soap with a clean damp
cloth. If all the dirt do not come off, re-
peat the procedure. Commercial foaming−
type vinyl cleaners are also available
which work well. Follow the manufacturer’s
instructions.

NOTICE

Do not use solvent, thinner, gasoline
or window cleaner on the interior.

Cleaning the interior

«
...
67
68
69
70
71
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: UMBRA RIMORCHI Pages: 18

Brand: FormFit Pages: 2

Chevrolet Silverado 2500HD 2021

Brand: GMC Pages: 433

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

Brand: Whispbar Pages: 15

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

Brand: Ford Pages: 8

Brand: Intec Pages: 16

Evo All THAR-FOR3

Brand: Fortin Pages: 7

Brand: Prorack Pages: 20

Brand: Park-Daddy Pages: 22

Brand: GAC MOTOR Pages: 356

Brand: Magneti Marelli Pages: 2

ASENTO EV-COLC15R

Brand: ADAPT SOLUTIONS Pages: 22

Brand: Hyundai Pages: 380

COOPER Convertible

Brand: Mini Pages: 168

ProPlus 620066V01

Brand: PAT Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands