TOX PRESSOTECHNIK TOX-FinePress PFL 002 Original Operating Instructions Download | Manualshive

Page: 48 / 72

background image

Operation

48

TOX_Manual_FinePress_PFS-PFL-PFW_en

8.5

Fine adjustment of working stroke

1

2

3

1

Fixing screws

2

Adjusting ring

3

Reference scale

1.

Loosen the fixing screws.

2.

Turn the adjusting ring to adjust the open height.
A line on the scale of the adjusting ring corresponds to a height adjust-
ment of 0.05 mm.
Turning clockwise - increases the open height.
Turning anti-clockwise - reduces the open height.

3.

Tighten the fixing screws.

«
...
46
47
48
49
50
...
»

Summary of Contents for TOX-FinePress PFL 002









































































Reviews:

No comments

Related manuals for TOX-FinePress PFL 002

Brand: Kelvin Pages: 2

Brand: Toku Pages: 7

Pocket-Hole Jig 7pce

Brand: Triton Pages: 20

Brand: S.E.F.A Pages: 26

Brand: Yokota Pages: 8

Brand: Fein Pages: 59

Brand: Gude Pages: 44

Brand: Hamamatsu Photonics Pages: 35

Brand: Napa Pages: 20

Brand: blackburn Pages: 8

Brand: Dynabrade Pages: 18

Brand: Truper Pages: 24

GALAXY EVO EGX850EWT

Brand: ENERMAX Pages: 60

Mobile Power Pack

Brand: Socket Pages: 2

Brand: Agilent Technologies Pages: 18

Brand: YASKAWA Pages: 35

Brand: TAAG Pages: 4

Brand: RHYNO Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands