TOX PRESSOTECHNIK EQe-K Original Operating Instructions Download Page 33

Page: 33 / 70

Installation

TOX_Manual_ElectricPowerDrive_EQe-K_en

6 Installation

6.1

Safety during installation

The installation may only be carried out by trained and authorized person-
nel.

DANGER

Electrical hazards in case of contact with live parts!

Electric shock, burns or death in case of contact with live parts!

Have all work on the electrical equipment performed by an electrician.

Disconnect power supply.

Wait for residual energy to disspate safely (at least 3 minutes).

WARNING

Hazard from suspended loads!

Severe crushing, impacts and serious accidents as a result of improper
transportation and falling load!

Only use lifting gear that is appropriate and in perfect technical condi-
tion, as well as load attachment devices with an adequate safe working
load.

Never stand or work under suspended loads.

Make sure that that no person is in the danger area.

When transporting and setting down, make sure that no parts of the
body become jammed.

Wear suitable personal protective equipment (e.g. safety boots).

CAUTION

Tripping points from laid supply lines!

Injuries from tripping and falling!

Avoid tripping points when setting up.

Mark unavoidable tripping points with warning sign.

Summary of Contents for EQe-K







































































Search results

Summary of Contents for EQe-K

Reviews:

Related manuals for EQe-K

Brands by name

Popular brands

TOX PRESSOTECHNIK EQe-K, Original Operating Instructions

Search results

Summary of Contents for EQe-K

Reviews:

Related manuals for EQe-K

Brands by name

Popular brands