manualshive.com logo in svg

Town & Country Fireplaces TCWS.38NG04.C, Instructions For Intallation, Page: 13 / 16

Share
Download
Town & Country Fireplaces TCWS.38NG04.C Instructions For Intallation Download Page 13

 

 

NOT SHOWN

*

*

*

*

TCWS.38NG04.C 050809-16

ITEM .......DESCRIPTION ............................................PART NO.

#1..........TRANQUILITY BURNER KIT........TCWS.38NG04.C

#2..........PEBBLE ASSEMBLY ......................... 5096.921  (3)

#3..........FUEL SUPPLY TUBE ......................... 5019.223

#4..........PILOT ASSEMBLY..........................TCRP.5005025C

#5..........ORIFICE, NATURAL GAS (#40) ......... 5022.3

ITEM.......DESCRIPTION ............................................PART NO.

#7 .........PROPANE CONVERSION KIT......TCWS.38LPCE01

#8 .........SAND .................................................. TC36.SAND50

                                                                      

#9..........TRIM ROCK “A”.......................................... 5096.922

(WHEN ORdERING, INClUdE PaRT NUMbER WITH dESCRIPTION)

1

2

5

3

4

4

KIT CONTENTS:

13

Replacement Parts

Summary of Contents for TCWS.38NG04.C

















Reviews:

No comments