background image

2

PREFLIGHT PREPARATIONS

Pay special attention to all precautions and warnings to ensure the safest operation. 
This radio system is intended for sport and recreational fl ying of R/C models only. 
Tower Hobbies is not responsible for incidental damage or personal harm resulting 
from improper usage or unauthorized alteration of this product. Physical modifi cations 
of any component in this system will void the warranty. For best results, make sure 
all batteries are new (if alkalines) or fully charged (if rechargeable). Connect servos 
to the receiver and try to adjust the radio on the workbench while reading along with 
this instruction manual to understand all functions.

TRANSMITTER

Reversing Switches

On/Off Switch

Trim Lever

Power Indicator LED

Neck Strap Eyelet

Trainer Switch

%

,

%

6

!

4

/

2

AILERON

4

(

2

/

4

4

,

%

RUDDER

INPUT POWER:

 This transmitter (Tx) requires four “AA” 

batteries. Non-rechargeable 1.5V alkaline or rechargeable 
1.2V nickel-cadmium (NiCd) or nickel-metal hydride 
(NiMH) cells can be used (not included). Do not mix old 
and new cells, or mix non-rechargeable alkaline cells with 
rechargeable NiCd or NiMH cells, etc. See the Accessories 
section at the end of this manual for optional batteries.

To install the batteries, slide open the battery door. Install 
the batteries as shown in the diagram. Make sure to note 
the proper polarities on each cell. Close the battery door.

Summary of Contents for 424

















Reviews: