Touchstone Whisper Lift II PRO Advanced Manual Download Page 4

Whisper Lift II PRO Advanced Swivel TV Lift 

 

   

www.touchstonehomeproducts.com

       

800.215.1990

 

 
 

4

Safety

 

 

Mounting  your flat screen TV to the Touchstone Whisper Lift II PRO Advanced Swivel TV Lift is fast and easy.  
Operating your lift is very straightforward.  However, to avoid the risk of personal injury and to ensure optimum 
performance of your TV lift mechanism, please pay particular attention to the warnings and safety notices 
throughout this manual. 

 
IMPORTANT SAFETY and PRE-INSTALLATION INSTRUCTIONS 

 

1.

 

Please adhere to the proper installation procedure as detailed in the installation instructions. 

 

2.

 

Safety precaution measures must be practiced at all times during installation of this product. 

 

3.

 

The entire installation instructions should be fully read and understood before beginning installation. 

 

4.

 

At least two people should be available to lift the TV onto the lift mechanism.  Please take care when 
handling your flat screen TV, as injury and damage can result from dropping or mishandling of the TV. 

 

5.

 

Plasma screen TVs should remain upright at all times.  Never place the screen face down on the floor.  This 
could cause damage to the TV. 

 
6.

 

The stand on your flat screen TV is removable!

  Please remove the stand prior to installing the TV on the 

lift mechanism.  Consult your TV’s owner’s manual for instructions for removing the stand. 

 
7.

 

Carefully measure all dimensions of your LCD, PLASMA, or LED TV before proceeding.  Then consult the 

Mounting and Installing the TV

 section of this manual for maximum TV size. 

 

IMPORTANT!:

 After installing your TV, you may find there is room in the bottom of the cabinet to install 

a small cable/satellite TV box.  Carefully inspect the space between the bottom of the TV and the bottom of 
the cabinet to see if your component will fit in the bottom of the cabinet.  Consult the 

Mounting and 

Installing the TV

 section of this manual for more information. 

 
8.

 

All cords connecting components to the TV should be a minimum of 72” (6 feet) in length when installing 
components inside of a cabinet or a minimum of 144” (12 feet) in length when installing components 
outside of cabinet (length of cable will depend on placement of your component). 

 
9.

 

WARNING!:

 TV lift mechanism contains moving parts.  Please keep hands, arms, and fingers away from 

the lift and cabinet lid opening when the lift is in motion.  Cables should be wire-tied or secured neatly so 
lift does not contact them during operation.  Also, keep all components away from the lift mechanism. 

 

Contact Touchstone Customer Service at 1-800-215-1990 with any questions regarding the operation of your Whisper Lift 
II PRO Advanced Swivel TV Lift.  We are also available on the web at 

www.touchstonehomeproducts.com

 

Summary of Contents for Whisper Lift II PRO Advanced





























Reviews: