background image

 

 

11

Remote Control &Control Panel Operation

  

 

(Control panel POWER switch must be ON to use remote control.) 

BUTTON 

FUNCTION 

ACTION & INDICATION 

 

POWER 

ON

: Enables control panel functions and 

remote control. Turns on flame effect. 

OFF

: Disables control panel functions and    

remote control. Turns off flame effect. 

1. 

Press once

. Indicator light turns on.  

Power turns on. All functions enabled. 

2. 

Press again

. Flame effect turns off. Unit 

goes to standby. All functions turn off.  

 

TIMER

 

TIMER button

: Controls timer settings to 

turn off fireplace at selected time.  
Settings range from 0.5 hours to 7.5 hours.  

1. 

Press once

. Indicator light turns on.  

Timer is set to 0.5 hours. 

2. 

Press again until desired setting is 

reached

. Indicator lights show setting. 

 

 

FLAME  

FLAME  button

: Makes flame effect 

dimmer and brighter. 

NOTE:

 Flame effect stays on until power 

button is turned off. Flame effect must be 
on for fireplace to turn on.

 

1. 

Press once

. Flame brightness effect 

gets changing.  
2. 

Press again.

 until desired setting is 

reached.  

 

 

COLOR   

COLOR  button

: Makes the  color flame 

effect changing. 

NOTE:

 color effect stays on until power 

button is turned off. Color flame effect 
must be on for fireplace to turn on.

 

1. 

Press once

. Flame color effect gets 

changing.  
2. Press again until desired setting is 
reached.total 3 colors. 

 
 

NOTICE 

When the fireplace is first turned on, a slight odor may be present. This is normal 
and  should  not  occur  again  unless  the  fireplace  is  not  used  for  a  long  period  of 
time. 

 

NOTICE 

To improve operation, 

aim

 the remote control at the front of the fireplace. 

DO NOT 

press the buttons too quickly

. Give the unit time to respond to each command.  

 

Remote Control Battery Information 

  This remote control uses TWO AAA 

 battery (not 

included

).

 

  Instructions for battery installation are on

 

the Remote Control battery compartment.  

 

NEVER 

dispose of batteries in 

fire. 

Failure to observe this precaution 

may result in an 

explosion

.

 

Dispose of batteries at your local hazardous material processing center.

 

 
 
 
 
 
 
 

Summary of Contents for BEF-50BIF














Reviews: