background image

iii

CE MARK

This device complies with the requirements of the EEC directive 2014/30/EU with 
regard to “Electromagnetic compatibility” and 2014/35/EU “Low Voltage Directive”.

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the following 
two conditions:
(1) This device may not cause harmful interference. 
(2) This device must accept any interference received, including interference that may 
cause undesired operation.

CAUTION ON LITHIUM BATTERIES

There is a danger of explosion if the battery is replaced incorrectly. Replace only 
with the same or equivalent type recommended by the manufacturer. Discard used 
batteries according to the manufacturer’s instructions.

Battery Caution

Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery 
according to the local disposal instructions.

Safety Caution

Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related 

OHJLVODWLRQSHULSKHUDOVVKDOOEH´0DWHULDOVIRUÀUHHQFORVXUHµFRPSOLDQW

0DWHULDOVIRUÀUHHQFORVXUHV

For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a 

),5((1&/2685(LQWKHWKLQQHVWVLJQLÀFDQWZDOOWKLFNQHVVXVHGVKDOOEHRI9&/$66

MATERIAL or shall pass the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY 
EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall 
thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1

Summary of Contents for Pulse Ultra Touch Monitor 17























Reviews: