4
5
Use condition and attentions in construction
Use condition
Attentions in construction
Warning
Warning: it means that ignoring this mark and misoperation may cause serious
personal injury and death.
Attention: it means that ignoring this mark and misoperation may cause personal
injury or property loss.
1.
2. The temperature for water supply is 4~60ºC. It is suggested to use the temperature
below 60ºC. Do not use steam to supply hot water.
3. The ambient temperature for use is 1~40ºC. If the ambient temperature is lower than
0ºC, the faucet will deform and crack from freezing.
4. To prevent internal spinkler damage,the water outlet temperature on the spinkler side
shall not exceed 60
℃
,it is suggested to use a temperature below 45
℃
.
5. Being out of use for a long time may result in internal and external rust to the faucet
and being unable to be used.
6. If you want to scrap this product, do not treat it as you do for general household
garbage. Please follow relevant statutes to have it treated, recovered and collected
appropriately by an independent recovery system.
7. The product in these instructions has a cleaning function.
1. The hot water supply side of the faucet is in a condition of high temperature.
Do not allow skin to contact with the hardware surface directly. Otherwise, scalding
may occur.
2. Do not reverse cold*hot water pipes. Otherwise, scalding may occur.
3. Do not use steam to supply hot water. Otherwise, scalding may occur.
4.The water temperature will change when switch from spout to shower or switch from
shower to spout.The user should test it by hand.otherwise,scalding may occur.
Minimum pressure………………0.05MPa
(
flow pressure
)
Maximum pressure………………0.75MPa
(
static pressure
)
Recommended Operating pressure…………
single function 0.12MPa
(
flow pressure
)
-0.5MPa
(
flow pressure
)
multi function 0.15MPa
(
flow pressure
)
-0.5MPa
(
flow pressure
)
1. Do not impact the product. Otherwise, failure, water leakage may occur.
2. It is imperative to use a neutral detergent in cleaning. Other detergents than a
neutral one may damage the plating coat or make the surface discolor.
3. Do not use any such detergent as acidic detergent and abstergent, polishing
powder, etc.containing thick particles and nylon brush. Otherwise, the plating
coat may be damaged, etc.
4. It is allowed to use a piece of soft cloth to wipe or use from time to time a
piece of cloth immersed in machine oil or vehicle wax to wipe. However, do
not contact with resin components. Otherwise, they may lose the gloss and
become rusty.
5. It is suggested not to leave it unused for a long time. Otherwise, this may lead
to internal and external rust to water nozzle to such a degree that it cannot be
used any more, etc.
6. With the product design being updated constantly, the physical object may not
coincide with the figure. However, the basic principle for installation, use is the
same.
Maintenance
Attentions
Nozzle
.
.
.
Summary of Contents for TBW01008B2
Page 2: ...1 2 1 2 3 4 5 6 7 8 10 11 1 1 1 1 TBW01008B2 TBW01008B2 PG TBW01010B2 TBW01010B2 PG 1 2...
Page 4: ...5 6 1 2 3 1 2 3 4 5 6 TBW01008B2 TBW01010B2 110 G1 2 2 8 24 2 mm L 1600 0 30...
Page 5: ...7 8 1 TBW01008B2 O TBW01031B mm G1 2 4 2 35 17 65 35 68 38 4 G1 2 63...
Page 6: ...3 10 9 2 TBW01031B O 1...