6
WARNING
Beware of irritation or burn.
Improper use of the toilet seat may cause irritation or burn.
When sitting for a long time on the toilet seat, switch the toilet seat temperature adjustment to "OFF".
When any of the following persons use a heated seat or warm air drying, someone should switch
the toilet seat temperature adjustment to "OFF" and switch the drying air temperature to "Low".
Young children, the aged and other users unable to set the temperature appropriately themselves.
The ill, physically disabled and others who do not have freedom of movement.
Those using any medicines that cause drowsiness (sleeping or cold medicine), those who have
been drinking heavily, anyone severely fatigued and anyone else liable to fall asleep.
This is an electrical product. Do not install it anywhere water is likely to get on
the product or anywhere with humidity high enough that water is likely to form
on the surface of this product. When using the product in a bathroom, install
a fan or ventilation port and ensure good air
fl
ow through the bathroom.
Failure to do so may cause
fi
re or electrical shock.
Always connect the NEOREST to the cold water supply.
Connecting to hot water supply may result in burns and equipment damage.
Check that an appropriate ground is installed.
(Asia, Oceania, Middle East)
If the ground is not installed, if there is a breakdown or electrical current leak, the lack of a
ground could cause electrical shock.
For the ground, use copper wire with a ground resistance of 100
Ω
max. and a diameter of 1.6 mm (0.005 ft ) min.
* If there is no ground installed, ask the contractor who did the installation to install the ground.
Make sure that a properly grounded (3 prong) outlet has been installed.
Failure to install a grounded outlet could cause electrical shock in the event of a malfunction or short circuit.
Check that the outlet for electrical power is as follows.
(Asia, Oceania, Middle East)
Failure to do so may cause
fi
re or electrical shock.
a. Protect the outlet circuits with a high-sensitivity quick leakage switch (with a rated current
sensitivity of 15mA or less) or an insulating transformer (1.5kVA min., 3kVA max.).
b. Install the outlet and plug positioned at least 0.8 m (2.62 ft) above the
fl
oor and as far as possible from the bathtub.
* Check that the wiring in a. and b. above is complete. If the wiring has not been completed, ask
the contractor who did the installation to do it.
Insert the power plug securely into the outlet.
(North, Central, South America)
Failure to do so may cause
fi
re, heat or short circuit.
Check that the power plug is waterproofed with silicone rubber.
(Asia, Oceania, Middle East)
A power plug that is not water-proofed may cause
fi
re and electrical shock.
* If the power plug is not water-proofed, ask the contractor who did the installation to water-proof it.
To unplug, hold the plug, not the cord.
Do not unplug by pulling the cord.
Pulling on the cord may cause damage and result in
fi
re or heat.
If the electric cord is damaged, avoid danger by having the manufacturer’s
repair department or equivalent specialist replace it.
Always disconnect the power plug from the outlet before cleaning,
maintenance or inspection.
Always switch the breaker on the distribution board to OFF.
(Asia, Oceania, Middle East)
Failure to do so may cause electrical shock or malfunction.
* Except when using "Wand cleaning" or "Bowl unit cleaning".
Periodically remove dust and dirt from the electrical plug and make sure it is
securely plugged into the wall outlet.
(North, Central, South America)
Failure to do so may cause
fi
re, heat or short circuit.
Pull the plug out from the outlet and wipe clean with a dry cloth.
Safety Precautions
(Continued)
D08781S_EN.indb 6
D08781S_EN.indb 6
11/12/2015 2:23:23 PM
11/12/2015 2:23:23 PM
