Burner Type
No. of burners
Jet size
Gas consumption
Auxiliary
1
0,50 mm
65 g/h
Semi Rapid
2
0.65 mm
120 g/h
Rapid
1
0.80 mm
182 g/h
Grill Oven burner
1
0,70 mm
160 g/h
Bottom oven burner
1
0,75 mm
170 g/h
Burner Type
No. of burners
Jet diameter
Gas consumption
Auxiliary
1
0,50 mm
65 g/h
Semi Rapid
2
0.65 mm
120 g/h
Rapid
1
0.80 mm
182 g/h
Ultra Rapid
1
1,07 mm
335 g/h
Grill Oven burner
1
0,85 mm
195 g/h
Bottom oven burner
1
0,92 mm
210 g/h
Table of Specifications Model F9H50G2 (03/T800)
Table of specifications model F6T40G2 (03/T700)
Fig. 2
Cooker burners, Oven and Grill control panel
Oven burner
Oven burner
Right rear
burner
Right rear
burner
Right front
burner
Right front
burner
burner
Left front
Left front
burner
Left front
burner
burner
Left front
Centre
burner
Grill burner
Grill burner
Model F9H50G2 (03/T800)
grill and oven
burners
Ignitor button
Ignitor button
grill and oven
burners
Ignitor button
cooker
burners
Ignitor button
cooker
burners
Off position
Fig. 1
Cooker burners, Oven and Grill control panel
Oven burner
Oven burner
Right rear
burner
Right rear
burner
Right front
burner
Right front
burner
Left front
burner
burner
Left front
Left rear
burner
Left rear
burner
Grill burner
Grill burner
Model F6T40G2 (03/T700)
Ignitor button
grill and oven
burners
Ignitor button
grill and oven
burners
Ignitor button
cooker
burners
Ignitor button
cooker
burners
Off position
Never let water dry or evaporate on the cleaned surfaces as this may cause stains . It is best to dry the cleaned surfaces immediately after
cleaning.
Whilst it is acceptable to wash the burner caps in a soapy water solution it is best to simply wipe the burners wit a damp cloth soaked in a
detergent solution rather than to immerse them. Be sure to make sure the burners and burner caps are dry before replacing them in their original
positions.
In the event that water does get into the burner ports, remove the burners from the stove and shake them dry. Also blow through them to make
sure that no water remains in the burners before placing them back on the stove.
Be careful when using proprietary oven cleaners as these may damage the oven surface. A soapy detergent is the best option .
Clean the stove top and oven afer every use to prevent the build up of fat or food particles which if left may be difficult to remove.
To clean the enameled and stainless steel surfaces of the appliance use a wet cloth or non abrasive sponge and a mild soapy detergent.
Abrasive cleaners and scourers should not be used as this may permanently damage the surface.
There are no preset maintenance periods for this appliance but it is recommend that the stove be examined by a qualified technician on and
annual basis.. This will ensure continued effective and safe operation of the appliance.
When cleaning the area around the burners never let water get into the burner ports as this may prevent them from igniting or operating correctly.
The pot support grids may be immersed in a soapy solution in order to clean them. Take note of the locations for the pot supports to make sure
they are firmly in place once refitted.
Cleaning and maintenance
To remove the burners from the stove top, firstly remove the pot support grids an place them to one side. Lift off the burner caps from the burners
and then lit out the burners from the stove top, noting the relative positions of the medium and large burners.(See Figs. 2 & 3)
