background image

For Outdoor Use Only

Important: Read these instructions for use carefully so as to familiarise yourself with

the appliance before connecting it to its gas container. It is also important to follow the

assembly instructions. Keep these instructions for future referenc

e

LPGSASA PERMIT NUMBER 1051

RSA-

A

-147/1-

12/

Safe Appliance

LP Gas Safety Association

INSTRUCTIONS FOR USE AND ASSEMBLY

PRECAUTIONS

·

Leak test all connections after each cylinder
refill

·

Never check for leaks with a match or open
flame

·

Do not store or use petrol or other flammable
vapours and liquids in the vicinity of this or
other any other appliance

·

Any LPG cylinder not connected for use shall
not be stored in the vicinity of this or any other
appliance

WARNING

HAZARDOUS FIRE OR EXPLOSION MAY
RESULT IF INSTRUCTIONS ARE IGNORED

It is the consumer’s responsibility to see that the
heater is properly assembled, installed, and
taken care of. Failure to follow instructions in this
manual could result in serious bodily injury
and/or property damage

FOR YOUR SAFETY

IF YOU SMELL GAS:

·

Turn of gas supply at the cylinder.

·

Extinguish all naked flames

·

Do not operate any electrical appliances.

·

Ventilate the area.

·

Check for leaks as detailed in this manual

·

If odour persists, contact your dealer or gas
supplier immediately.

Model: 16/DK1025

Outdoor Patio Heater

Summary of Contents for 16/DK1025











Reviews: