Toshiba Strata CIX40 User Manual Download Page 138

Page: 138 / 208

User Programming

Feature Codes

120

Strata CIX IP5000-series Telephone UG 07/09

Feature Codes

Feature Access Codes are entered as a sequence on your telephone to use a particular feature.

For an example of Call Forward, see

“Call Forward Examples” on page 53

Table 17

Feature Access Codes

Feature

Feature Access Code Sequences

Account Code (while on a call)

Cnf/Trn

#46

, dial account code digits

Attendant Console

Ext.

Automatic Busy Redial - On

Cnf/Trn

#441

, hang up

Automatic Busy Redial - Off

Ext.

#442

Automatic Callback (while on a call)

when you hear busy tone

Automatic Callback Cancel

Ext.

#431

Background Music

Telephone Speaker On

Ext.

#490

+ music source no. (1~15) +

Telephone Speaker Off

Ext.

#491

Spkr

External Speaker On

Ext.

#492

+ music source no. (1~15) +

External Speaker Off

Ext.

#493

Spkr

Call Forward - See

Table 22 on page 171

Call Park

Activate

(while on a call)

Cnf/Trn

#33

+ Orbit Number (

7000

7019

) or an Ext.

No.

Retrieve

(while on a call)

Ext.

#32

+ Orbit Number (

7000

7019

) or an Ext.

No.

Call Pickup

Directed DN pickup of ringing or held
calls.

Ext.

#5#6

+ Ext. No

Directed DN pickup of ringing, held or
parked calls.

Ext.

#5#29

+ Ext. No. to be picked up

Incoming - Group Pickup

Ext.

#5#34

+ Group Number to be picked up

Incoming - Directed Extension Pickup

Ext.

#5#5

+ Primary Ext. No to be picked up

Incoming - Directed Group Pickup

Ext.

#5#32

+ Group Number to be picked up

Incoming - Directed Extension Pickup

Ext.

#5#22

+ Ext. Number

All Call Page, Group Page and/or
External Page Pickup of page

Ext.

#5#36

+ Page Zone No. (01~08)

#5#5

+ Ext. No. of another phone being paged.

Call Pickup for calls on Hold

Local Pickup (call held on this phone)

Ext.

#5#71

Summary of Contents for Strata CIX40

















































































































































































































Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands

Toshiba Strata CIX40, User Manual

Search results

Summary of Contents for Strata CIX40

Reviews:

Related manuals for Strata CIX40

Brands by name

Popular brands