Toshiba Strata CIX IP5000 Series Page 35 User Manual Download

Page: 35 / 216

The Basics

Keystrip Labels

Strata CIX IP5000-series Telephone UG 04/09

Keystrip Labels

Available on 9 Line LCD telephone and 10 Button LCD Add-on Module



To program LCD Keystrip Labels

1. Dial

#9876

(or press the flexible

Program

button)

2. Press the

Speaker

button.

3. Press the button you wish to label.

4. Use the dialpad to enter the label.

5. Press the button labeled in step 3 to save the setting.

6. To label another button, repeat steps 3-5.

7. To exit User Programming mode lift the handset off-hook / on-hook.

Ring Tones



To set distinctive ringing

1. Press

#9876

to enter User Programming Mode.

2. Press a

Line

or extension button. The LED is steady green.

3. You can press

Hold

to switch between internal and external pitch. (Internal =

station calls within your system; external = outside line calls.)

4. Enter the two-digit pitch number (see

Table 5 on page 18

5. Press the same button that you pressed in Step 2 (

Line

or extension). Two beeps is

a confirmation tone and “DATA PROGRAMMED” displays on your LCD.

6. Lift the handset off-hook/on-hook to save settings.

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Search results

Summary of Contents for Strata CIX IP5000 Series

Reviews:

Related manuals for Strata CIX IP5000 Series

Brands by name

Popular brands

Toshiba Strata CIX IP5000 Series, User Manual

Search results

Summary of Contents for Strata CIX IP5000 Series

Reviews:

Related manuals for Strata CIX IP5000 Series

Brands by name

Popular brands