manualshive.com logo in svg

Toshiba Strata CIX IP5000 Series, User Manual

The Toshiba Strata CIX IP5000 Series offers advanced communication capabilities for businesses. Ensure optimal utilization of this product with our comprehensive User Manual. Download it for free at manualshive.com and unlock the full potential of your Toshiba Strata CIX IP5000 Series, hassle-free.

Share
Download
background image

Administrator Programming

IP Telephone Function Settings

Strata CIX IP5000-series Telephone UG     04/09

129

IP Telephone Function Settings

These steps enable you to turn On/Off button beeps, room noise cancellation, handset 
Busy Override, and headset volume control. You can also adjust the setting for carbon 
headsets vs. non-carbon headsets. 

1. Press 

3

+

6

+

9

+

Hold

 (simultaneously).

2. Press 

0

 then 

Hold

.

3. Press the Feature Buttons to turn the LEDs On/Off (see 

Table 18

).

4. Press 

Hold

 to set the above data.

5. Lift the handset off-hook / on-hook to save the settings. 

Table 18

IP Telephone Function Settings

FB

LED ON

LED OFF

FB1

Buttons beep. (Default)

Buttons do not beep.

FB12

Speakerphone/Microphone sensitivity 
is lower.

Speakerphone/Microphone sensitivity is 
normal. (Default)

FB4

Enable handset Busy Override (BOV) 
tone. 

Disable handset BOV. (Default)

FB6

Handset carbon supported.

Auto (default)

FB11

Turn LED On if carbon headset is 
attached.

Turn LED Off if carbon headset is not 
attached. (Default - recommended for GN 
Netcom Headset GN9330)

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Reviews:

No comments

Related manuals for Strata CIX IP5000 Series

Panasonic X60 Operating Instructions Manual preview
X60
Brand: Panasonic Pages: 140
Panasonic EB-3901 Important Information Manual preview
EB-3901
Brand: Panasonic Pages: 32
Damall D-2304 Setup Manual preview
D-2304
Brand: Damall Pages: 7
Unihertz Jelly User Manual preview
Jelly
Brand: Unihertz Pages: 97
Olitech EasyFlip OLT2908 User Manual preview
EasyFlip OLT2908
Brand: Olitech Pages: 57
H-TEK UC842 User Manual preview
UC842
Brand: H-TEK Pages: 142
Sony Ericsson Z500a User Manual preview
Z500a
Brand: Sony Ericsson Pages: 102
Mobistel Cynus T7 User Manual preview
Cynus T7
Brand: Mobistel Pages: 24
Videocon V1305 User Manual preview
V1305
Brand: Videocon Pages: 17
Alcatel-Lucent OmniTouch 8082 User Manual preview
OmniTouch 8082
Brand: Alcatel-Lucent Pages: 60
Yezz 45ELTE User Manual preview
45ELTE
Brand: Yezz Pages: 35
OUKITEL U7 Plus User Manual preview
U7 Plus
Brand: OUKITEL Pages: 39
GENERAL MOBILE discovery Manual preview
discovery
Brand: GENERAL MOBILE Pages: 56
Global G300 User Manual preview
G300
Brand: Global Pages: 50
Zte REEF User Manual preview
REEF
Brand: Zte Pages: 177
Philips CT0390BLK Specifications preview
CT0390BLK
Brand: Philips Pages: 2
Philips CT0392BLK Specifications preview
CT0392BLK
Brand: Philips Pages: 3
Philips CT0298BLK Specifications preview
CT0298BLK
Brand: Philips Pages: 2

Brands by name

Popular brands

Load more brands