background image

Connections

Depending on your TV and other equipment there
are various ways you can connect the player.
Please refer to the manuals of your TV, VCR, stereo
system or other devices as necessary for additional
connection information.

Notes:

The picture and sound of a nearby TV, VCR, or radio may
be distorted during playback. Position the units away from
each other or turn off the unit after removing the disc.

Make sure the DVD+VCR is connected directly to the TV
and tune the TV to the correct video input channel. 

Do not connect the DVD+VCR’s AUDIO OUT jack to the
phono in jack (record deck) of your audio system. Do not
connect the DVD+VCR via another VCR. The DVD image
could be distorted by the copy protection system. 

Connecting an Antenna 
or Cable TV

a

a

Antenna

:

Disconnect the antenna from the rear of the TV and
identify the antenna cable. If it is a round 75 ohm coaxi-
al cable connect it directly to the jack marked ANT.IN on
your DVD+VCR. If your antenna cable is flat connect it
to a 300-ohm to 75-ohm antenna adaptor (not supplied)
and slip the adaptor over the ANT.IN jack. Don’t attempt
to screw it into to the DVD+VCR.

b

b

Cable TV:

If your cable connection has no converter or descram-
bler, unscrew the cable from your TV and attach it to the
ANT.IN jack on the DVD+VCR. If a converter is required
connect a coaxial cable from the wall jack to the IN con-
nector on the converter, and a coaxial cable from the
OUT connector on the converter to the ANT IN on your
DVD+VCR. This cable hookup permits both TV and
DVD+VCR operation. 

To view or record a CATV channel

1. Tune the TV to the DVD+VCR output channel 

(CH 3 or 4).

2. Set the DVD+VCR channel selector to the cable out-

put channel. (Example: CH3)

3. Select a channel using the cable converter.

Notes:

With this connection, you cannot record one program while
viewing another.

If you are using a cable box to tune channels, it is not nec-
essary to do Auto Channel Set.

Basic TV Connections

Make one of the following connections, depending on
the capabilities of your TV.

12

Rear of DVD+VCR

Antenna

Antenna

OR

OR

a

b

Rear of DVD+VCR

L

R

AUDIO INPUT

VIDEO 

INPUT

ANTENNA

INPUT

Rear of TV

A1

V

R

Y

Pb

Pr

COMPONENT/PROGRESSIVE SCAN

VIDEO INPUT

L

R

AUDIO INPUT

S-VIDEO 

INPUT

Rear of TV

S

A2

C

Summary of Contents for SD-V383SC











































Reviews: