Toshiba Satellite M60 Maintenance Manual Download Page 56 | Manualshive

Page: 56 / 214

background image

2 Troubleshooting Procedures

2.8 TouchPad Troubleshooting

2-22

[CONFIDENTIAL]

Satellite M60/M65 Series Maintenance Manual

To determine if the computer’s built-in TouchPad is functioning properly, perform the following
procedures. Figure 2-9 outlines the process. Start with Procedure 1 and continue as instructed.

Procedure 1: TouchPad connection check

Procedure 2: TouchPad replacement check

Procedure 1

TouchPad connection check

The TouchPad is connected via the TouchPad FPC to the system board. Make sure the TouchPad
FPC cable is firmly connected to the TouchPad and system board. Refer to Chapter 4,

Replacement Procedures,

for instructions on how to disassemble the computer and then perform

the following checks.

If any of the connections are loose, reconnect firmly. If any of the connections is damaged, or
there is still an error, go to Procedure 2.

Procedure 2

TouchPad replacement check

The TouchPad unit or FPC may be defective or damaged. Replace each with a new one
following the steps in Chapter 4. If the FDD is still not functioning properly, replace the system
board with a new one following the steps in Chapter 4.

«
...
54
55
56
57
58
...
»

Summary of Contents for Satellite M60























































































































































































































Reviews:

No comments

Related manuals for Satellite M60

Brand: IBM Pages: 110

Brand: IBM Pages: 331

Brand: FIC Pages: 128

Brand: bto Pages: 216

Brand: Fujitsu Pages: 32

Brand: Fujitsu Pages: 2

Brand: Fujitsu Pages: 2

LIFEBOOK U9311A

Brand: Fujitsu Pages: 2

Brand: Fujitsu Pages: 61

Brand: Fujitsu Pages: 82

LIFEBOOK U9312X

Brand: Fujitsu Pages: 105

Brand: Fujitsu Pages: 83

LIFEBOOK U9311A

Brand: Fujitsu Pages: 79

Brand: Fujitsu Pages: 6

Brand: Lenovo Pages: 84

2384EHU - ThinkPad G40 2384

Brand: Lenovo Pages: 164

Brand: Lenovo Pages: 34

Brand: Lenovo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands