Toshiba Satellite E200 Maintenance Manual Download Page 175 | Manualshive

Page: 175 / 243

background image

4.11 CPU Cooling Module and Fan

4 Replacement Procedures

Satellite/E200/E205 Maintenance Manual

4-33

Installing the CPU Cooling Module and Fan

Install the cooling Module according to the following procedures and Figures 4-15, 4-16,
4-17 and 4-18.

CAUTION:

When installing the cooling module, keep the following in mind:

1. Be sure to confirm the correct position for the module.

2. Secure the relevant screws on the main board according to the number sequence

sealed on the heat sink module.

NOTE:

Apply silicon grease with a special syringe to cover the surface of the CPU chip

completely.

1.

If the thermal pad is broken, replace new thermal pad into correct position, thermal
pad part number V000934140 for Mainz10 and V000941970 for Mainz10G.

2.

If silicon grease is already applied to the CPU and fan module, wipe it off with a
cloth.
By using a special syringe, apply silicon grease G7762 to the CPU chip center so that
the entire CPU chip is covered with the grease G7762.

3.

Install the CPU cooling module into the correct position on the system board.

4.

Place the CPU cooling module in the correct position and secure it with six CPU
thermal module securing screws.

5.

Place the fan in the correct position and secure it with one M2x6 black flat head
screw.

6.

Connect the fan cable to CN4300 on the system board.

«
...
173
174
175
176
177
...
»

Summary of Contents for Satellite E200




















































































































































































































































Reviews:

No comments

Related manuals for Satellite E200

Brand: Gateway Pages: 12

Brand: IBM Pages: 2

Brand: IBM Pages: 189

Brand: IBM Pages: 147

Toughbook CF-52EKMBGAM

Brand: Panasonic Pages: 22

Brand: IBM Pages: 222

Brand: IBM Pages: 132

Brand: Fujitsu Pages: 32

Brand: Asus Pages: 28

Brand: Asus Pages: 23

Disney Netpal MK90H

Brand: Asus Pages: 68

Brand: Asus Pages: 20

Brand: Asus Pages: 112

Brand: Asus Pages: 96

Brand: Asus Pages: 104

C213NA-BW0034-OSS

Brand: Asus Pages: 98

Brand: Asus Pages: 102

Brand: Asus Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands