Toshiba Satellite A350 Series Maintenance Manual Download Page 191

Page: 191 / 297

4 Replacement Procedures

Error! Style not defined. Error! Style not defined.

4.4

Memory

Removing the Optional Memory

Remove the optional memory according to the following procedures and Figure 4.6 after
checking that the laptop is turned off.

CAUTION: Remove the optional memory after turning off the laptop. If this is violated, the
laptop or memory can be damaged.

Turn the laptop upside down.

Remove one M2.5x5.4 screw that secures the RAM door.

Remove the RAM door.

CAUTION: Do not touch the connectors on the memory or in the laptop. Contaminated
connectors can cause memory access problems.

M2.5X5.4

＊

Figure

6 Removing the RAM door

Satellite A350D Maintenance Manual

4-14

Downloaded from LpManual.com Manuals

Summary of Contents for Satellite A350 Series










































































































































































































































































































Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands

Toshiba Satellite A350 Series, Maintenance Manual

Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands