Toshiba Satellite A350 Series Maintenance Manual Download Page 187

Page: 187 / 297

4 Replacement Procedures

Error! Style not defined. Error! Style not defined.

4.3

HDD

Removing the HDD

CAUTION: Do not press on the top or bottom of the drive.
Applying such pressure can either corrupt the data in the drive
or damage the drive.

There are two HDD equipped in the laptop. Remove the HDD (hard disk drive) according to the
following procedures and Figure 4.2, 4.3, 4.4, 4.5.

To remove the main HDD, remove two M2.5x6 HDD door screws that secure the HDD
and then remove the HDD door.

M2.5X6

＊

Figure

2 Removing the main HDD door

Satellite A350D Maintenance Manual

4-10

Downloaded from LpManual.com Manuals

Summary of Contents for Satellite A350 Series










































































































































































































































































































Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands

Toshiba Satellite A350 Series, Maintenance Manual

Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands