EN
EN
EN
EN
EN
EN
EN
1
e
s
n
h
k
c
o
q
i
b
g
f
d
a
m
j
r
p
l
1
PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and
remove the air fi lters.
2. Attach the attachment fi lters
(see detail in the accessory
sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new alkaline batteries
(AAA type) following the (+)
and (–) positions.
Removing the batteries
1. Remove the cover, and take out the batteries.
2. Reattach the cover.
• Please dispose of the batteries according
to the local regulation.
Clock Setup
1. Push
by tip of the pencil.
If timer indication is fl ashing, go to
the next step 2.
2. Press
or
: adjust the
time.
3. Press
: Set the time.
Remote Control Reset
1. Remove the batteries.
2. Press
.
3. Insert the batteries.
Remote Control Caring
1. Clean the remote control with a wet cloth when needed.
2. No benzine, thinner, polishing powder or chemically-
treated duster.
2
REMOTE
CONTROL
1
Infrared signal emitter
2
Start/Stop button
3
Mode select button (MODE)
4
Temperature button (TEMP)
5
Fan speed button (FAN)
6
Swing louver button (SWING)
7
Set louver button (FIX)
8
Weekly timer setting button
9
Memory and Preset button
(PRESET)
!
8°C heating operation
button
(8°C)
"
High power button
(Hi-POWER)
#
Economy button (ECO)
$
Comfort sleep button
(COMFORT
SLEEP)
%
Floor warming
mode button (FLOOR)*
&
Clock Reset button (CLOCK)
(
Check button (CHECK)
)
Reset button (RESET)
~
Filter reset button (FILTER)
+
Power selection button (POWER-SEL)
3
AUTOMATIC / COOLING (DRY) /
HEATING / FAN ONLY OPERATION
1. Press
: Select Auto A, Cool
, Dry
, Heat
, or
Fan only
.
2. Press
: Set the desired temperature.
Min. 17°C, Max. 30°C.
3. Press
: Select AUTO, LOW , LOW+
, MED
,
MED+
, HIGH
, and Quiet (
).
※
AUTOMATIC OPERATION : Choose cooling or heating
operation automatically.
※
In DRY OPERATION mode, it can not select air volume.
※
In FAN ONLY OPERATION mode, it does not show setting
temperature.
Insert direction of
(+) and (-) correctly
Pull the cover
away fi rmly.
4
Hi-POWER
OPERATION
To automatically control room temperature and airfl ow for faster
Auto, cooling or heating operation (except in DRY mode).
Press
: Start and stop the operation.
6
ECO
OPERATION
To automatically control room to save energy (except in DRY
mode).
Press
: Start and stop the operation.
Note:
Cooling operation; the internal set temperature will
increase automatically 1 degree by 2 hours (maximum
2 degrees increase). For heating operation the internal
set temperature will decrease.
7
TIMER
OPERATION
Set the timer when the air conditioner is operating.
Setting the ON Timer
Setting the OFF Timer
1
Press
: Set the
desired
ON timer.
Press
: Set the
desired
OFF timer.
2
Press
: Set the
timer.
Press
: Set the
timer.
3
Press
: Cancel the
timer.
Press
: Cancel the
timer.
Setting the ON-OFF Timer
1
Press
: Set the
ON timer.
3
Press
.
2
Press
: Set the
OFF timer.
4
Press
: Cancel
the timer.
Note:
• Keep the remote control in accessible transmission to the
indoor unit; otherwise, the time lag of up to 15 minutes will
occur.
• The setting will be saved for the next same operation.
5
FLOOR WARMING OPERATION
Heating will operate with downward blowing only.
Temperature of air outlet will be higher than usual.
* Floor can work only if indoor unit is Bi-fl ow console.
1112150109_01_EN.indb 1
2/11/58 BE 3:39 PM
