background image

12

ELECTRICAL WORKS

The power supply can be selected to connect to indoor unit or outdoor unit. Choose proper way and connect the power supply and connecting cable by follow 

the instruction as following.

Model

RAS-10PKVPG-E

RAS-13PKVPG-E

RAS-16PKVPG-E

Power source

50Hz, 220-240 V Single phase

Maximum running current

8.50A

10.00A

10.50A

Circuit breaker rating

10.50A

12.50A

13.50A

Power supply cable

H07RN-F or 60245 IEC66 (1.5 mm

2

 or more)

Connecting cable

Wiring of the cable can be carried out without removing the main panel.

1.  Remove the front panel.

  Pull and lift up front panel until it stops, move arms on left and right side 

to outward direction then pull toward you to remove front panel.

 

w

  Beware front panel fall down that may cause of injure or part damage.

Arm

Arm

2.  Remove the terminal cover and cord clamp.

3.  Insert the cable (according to the local cords) into the pipe hole on the 

wall.

4.  Take out the cable protrudes about 20 cm from the front.

5.  Insert the cable fully into the terminal block and secure it tightly with 

screws.

6.  Tightening torque : 1.2 N·m (0.12 kgf·m)

7.  Secure the cable with the cord clamp.

8.  Fix the terminal cover and attach front panel to the indoor unit.

1.  Remove the valve cover from the outdoor unit.

2.  Connect the cable to the terminals as identified with their respective 

matched numbers on the terminal block of indoor and outdoor unit.

3.  When connecting the cable to the outdoor unit terminals, make a loop as 

shown in the installation diagram of indoor and outdoor unit to prevent 

water coming in the outdoor unit.

4.  Insulate the unused cords (conductors) from any water coming in the 

outdoor unit. Proceed them so that they do not touch any electrical or 

metal parts.

Wiring Connection

     Indoor unit

     Outdoor unit

Carry out attaching in the reverse order to removal.

Keep front panel horizontally and put both arms into guides.

Make sure both arms are inserted completely.

If the gap between main panel and front panel isn’t even, remove and attach 

again.

     How to attach the front panel

•  Be sure to refer to the wiring system diagram labeled inside the main 

panel.

•  Check local electrical cords and also any specific wiring instructions or 

limitations. 

CAUTION

Valve cover

Terminals block

Main panel

Terminal cover

Terminals block

Front panel

about 20 cm

Cable

Front panel

Main panel

Arm

Guide

01_1121451198-EN.indd   12

4/26/2561 BE   10:06 AM

Summary of Contents for RAS-16PKVPG-E


















Reviews: