manualshive.com logo in svg

Toshiba MY-1016, Service Manual

Share
Download
Toshiba MY-1016 Service Manual Download Page 19

MY-1016 DISASSEMBLY AND REPLACEMENT

6 - 4

October 2000 © TOSHIBA TEC

[F] SFB clutch pulley/SFB flange wheel

1. Remove SFB hinge unit. (See Fig. 6-1 to 6-4)

2. Remove SFB document tray assembly.

(See Fig. 6-6)

3. Detach SFB feed cover.

(See Fig. 6-11 and 6-13)

4. Detach stop ring and remove bushing.

5. Release 3 clamps and detach the harness.

6. Remove one screw and detach the ground wire.

Fig. 6-15

7. Remove 2 screws, release 2 tabs, slide SFB

feed roller assembly in the direction of the ar-

row, and remove SFB clutch pulley assembly.

Note:

Before attaching the SFB feed roller assem-

bly, loosen 2 screws securing the SFB feed

roller fixing plate.

Attach the SFB brake pad assembly (See

Fig. 6-10), then fix the SFB feed roller fixing

plate in place.

Stop ring

Bushing

Screw

Ground wire

Clamp

Harness

Bushing

SFB clutch
pulley assembly

SFB feed roller
assembly

Screw

SFB clutch motor

254

Clamp

5. Remove 2 screws, release 2 tabs, and detach

SFB feed cover.

Fig. 6-14

SFB feed cover

Screw

SFB feed assembly

Screw

253

Fig. 6-16

255

4. Release SFB pad spring and remove SFB brake.

Note:

Clean the SFB brake pad with a cloth moist-

ened with alcohol by pressing hard, and go-

ing back and forth on the brake pad more

than 20 times.

Fig. 6-13

SFB brake

SFB pad spring

252

SFB brake pad

SFB feed roller
fixing plate

Summary of Contents for MY-1016























Reviews:

No comments

Brands by name

Popular brands

Load more brands