manualshive.com logo in svg

Toshiba HDD2187, User Manual, Page: 8 / 11

Share
Download
Toshiba HDD2187 User Manual Download Page 8

 

 
 

 

6 

SPECIFICATIONS –MK2023GAS (HDD2187)  

General 

Model MK2023GAS 

(HDD2187) 

Interface ATA-2/3/4/5 
Motor 

Fluid Dynamic Bearing (FDB) 

Functionality

 

Formatted Capacity 

20.003GB*

Rotational Speed 

4200rpm 

Avg. Rotational Latency 

7.14/ms 

Spin-up Time 

4sec (typical) 

Buffer 2MB 
Seek Time (Average)  

12  

Internal Transfer Rate 

164.6 ~ 257.1 Mbits/sec (max) 

Host Transfer Rate  

100Mbytes/sec  

*Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes. 

 

Internal Drive Characteristics

 

Number of Disks 

1 

Number of Read/Write Heads 

2 

Track Density (TPI) 

72k 

User Data Cylinders 

34,040 

Logical Cylinders 

16,383 

Logical Heads 

16 

Logical Sectors/track 

63 

Bytes per Sector 

512 

Logical Blocks (LBA) 

39,070,080 

Reliability 

Preventative maintenance 

None 

Non-recoverable read errors 

1 error per 10

13

 bits read 

Electrical

  

Voltage 5V 

5% 

Power Consumption

 

Start 4.7W 

typ 

Seek 2.6W 

typ 

Read/Write 2.3W 

typ 

Sleep 0.1W 

typ 

Energy Consumption Efficiency 

0.035W/GB avg  

Shock 

Operating 1,960m/s

2

 (200G)(2msec) 

Non-Operating 7,840m/s

2

 (800G)(1msec) 

Summary of Contents for HDD2187












Reviews:

No comments