Toshiba GN-1060 Operator'S Manual Download Page 8 | Manualshive

Page: 8 / 56

background image

6 Precautions

(2) This device must accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.

Labelling

Toshiba TEC Wireless LAN Module GN-1060 labelled as below.

FCC ID: BJI-GN1060

The proposed FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is
installed into the system, “Contains FCC ID:BJI-GN1060” shall be placed on the outside of final host system.

Caution: Exposure to Radio Frequency Radiation.

To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be
maintained between the antenna of this device and all persons. This device must not be co-located or
operating in conjunction with any other antenna or transmitter.



Regulatory Notice for Channel Use in France

The number of channels that can be used for wireless LAN differs from country to country. In France however,
user only 4 channels (channel 10, 11, 12, 13) when using wireless networks.



Channel 10 (2457 MHz)



Channel 11 (2462 MHz)



Channel 12 (2467 MHz)



Channel 13 (2472 MHz)



Singapore Portion



Approved Countries/Regions for use for the Toshiba Wireless LAN

This equipment is approved to the radio standard by the specific countries/regions. Please ask Toshiba
authorized dealer or service engineer.



NOTES!



The unauthorized reproduction of this document, in whole or in part, is prohibited.



The specifications, designs, and other contents of this document are subject to change without notice.



The contents of this document are believed to be accurate, however if any discrepancies noted should be
brought to the attention of TOSHIBA authorized dealer or service engineer.



Notwithstanding the foregoing, the manufacturer is unable to accept any claims for losses or lost profits,
etc. Resulting from the use of this product.



TOSHIBA TEC will not guarantee the machine performance if you perform any setting other than specified
in this manual.

France limited to 2446.5-2483.5 MHz Indoor use.
Belgium limited to 2400-2483.5 MHz Indoor, 2460-2483.5 MHz Outdoor use.

«
...
6
7
8
9
10
...
»

Summary of Contents for GN-1060

























































Reviews:

No comments

Related manuals for GN-1060

Brand: D-Link Pages: 38

Web Smart DES-1210-28P

Brand: D-Link Pages: 6

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 23

Express EtherNetwork DI-604

Brand: D-Link Pages: 7

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 97

Brand: DAQ system Pages: 41

Brand: DAQ system Pages: 19

Brand: Accusys Pages: 34

Brand: Acqiris Pages: 22

Brand: Parker Pages: 50

Brand: UfiSpace Pages: 35

Brand: Point of View Pages: 13

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

Brand: ADS Technologies Pages: 1

Brand: Mitsubishi Pages: 874

Brand: Mellanox Technologies Pages: 57

Brand: ADTRAN Pages: 2

Brand: SriHome Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands