background image

 

E6581341 

 

■ 

Limitation of use

 

 Safety precaution

 

▼ 

Never use this unit with any device other than TOSVERT VF-AS1/PS1 series inverters. Doing so may 

cause an accident. 

 

■ 

General Operation

 

 

Warning

 

 

Disassembly 

prohibited

 

▼ 

Never disassemble, modify or repair. 

 

Doing so could result in electric shock, fire and injury. For repairs, call your sales 
agency. 

 

 

Prohibited

 

▼ 

Do not attach this option to any inverter other than the VF-AS1/PS1. 

 

Doing so could result in electric shock or fire. 

 

▼ 

Don't place or insert any kind of object into the ETB004Z (electrical wire cuttings, rods, 

wires). 

 

Doing so could result in electric shock or fire. 

 

▼ 

Do not allow water or any other fluid to come in contact with the ETB004Z. 

 

Doing so could result in electric shock or fire. 

 

 

Mandatory

 

  If the inverter begins to emit smoke or an unusual odor, or unusual sounds, immediately 

turn off the VF-AS1/PS1.   

If the equipment is continued in operation in such a state, the result may be fire. Call 
your local sales agency for repairs. 

  Do not touch the sharp portions (such as leads of parts on the board, the corner of 

board, or etc.) on this option. It may lead to injuries. 

 

Caution

 

 

Mandatory

 

  This option is an electrostatic discharge sensitive device. Handle it, where the 

environment is protected against electrostatic electricity. 
Otherwise, permanent damage to device will result. 

 
■ 

Transportation & installation

 

 

Warning

 

 

Prohibited

 

  Do not apply a dropping shock or other physical shocks.   

Otherwise, damage or malfunction will result.

 

  Do not install or operate the inverter if it is damaged or any part of it is missing.

 

Operating a defective inverter may lead to electric shocks or fire.   
For repairs, call your sales/repair agency.

 

▼ 

Do not put any flammable material near the product.

 

It may catch fire due to the product sparking in the case of a malfunction.

 

 

Mandatory

 

▼ 

Use this product under the environmental conditions prescribed in the instruction 
manual.

 

Usage it under any other conditions may result in malfunction. 

▼ 

An emergency stop device must be installed that fits with system specifications   
(e.g. shut off input power then engage mechanical brake). 
Operation cannot be stopped immediately by the inverter or this unit alone, thus risking 
an accident or injuries.

 

Summary of Contents for ETB004Z



















Reviews: