manualshive.com logo in svg

Toshiba EB621, Operation Manual

Share
Download
Toshiba EB621 Operation Manual Download Page 29

6F8C0879

17

3.1 Switch Setting

3

There are two 4-bit DIP switches in the front and side panel of EN651 and EN661. Each 
of switches for EN651 and EN661 is described in Table 3-3

Note:

This mode is valid for EN651 only. (Not applicable to EN661 dual systems. If this
mode is used, it is valid for line A only, provided that a single socket interface is
employed.)

Table 3-3  Operation Mode Setting Table (EN651, EN661)

Switch No. Name

Function

Setting

Default 

(Before 

shipment)

Front 
Panel

1

DL

Download

on:Download

off

2

IPF

IP address restriction 
(Note)

on : Free, off : Restricted

off

3

IP0

IP address type

IP1

IP0

Operation

IP1=off

IP0=off
(Class B 
setting)

off

off

Class B (General)

off

on

Reserve

4

IP1

on

off

TOSDIC-CIE 1200

on

on

Set from tool

Side 
Panel

1

M0

Operation mode

M1

M0

Operation

M1=off

M0=off
(Normal setting)

off

off

Normal

off

on

Reserve

2

M1

on

off

Reserve

on

on

Memory clearance

3

SEL

Spare 0

Reserve

4

GW

Relay function (future)

on : Provided, off : None

Table 3-4  Operation Mode Setting Table (EN651A)

Switch No. Name

Function

Setting

Default 

(Before 

shipment)

1

M0

Operation mode

M1

M0

Operation

M1=off

M0=off
(Normal setting)

off

off

Normal

off

on

Download

2

M1

on

off

Test program

on

on

Reserve

3

SL

Debug

on : WDT invalid, off : WDT valid

off

4

GW

Relay function (future)

on : Provided, off : None

off

5

S0

Spare 0

Unused

off

6

IPF

IP address restriction

on : Free, off : Restricted

off

7

IP0

IP address type

IP1

IP0

Operation

IP1=off

IP0=off
(Class B 
setting)

off

off

Class B (General)

off

on

Reserve

8

IP1

on

off

TOSDIC-CIE 1200

on

on

Set from tool

Summary of Contents for EB621



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands