background image

   

  D4222901M 

Copyright © 2013 - 2018 TOSHIBA TELI CORPORATION, All rights reserved.       

http://www.toshiba-teli.co.jp/en/index.htm

 

 

 

USAGE PRECAUTIONS 

 

Handle carefully 

Do not drop the equipment or allow it to be subject to strong impact or vibration, as such action may 
cause  malfunctions.  Further,  do  not  damage  the  connection  cable,  since  this  may  cause  wire 
breakage. 

 

Environmental operating conditions 

Do  not  use  the  product  in  locations  where  the  ambient  temperature  or  humidity  exceeds  the 
specifications.   
Otherwise, image quality may be degraded or internal components may be adversely affected. In 
particular, do not use the product in areas exposed to direct sunlight. 

 

Combination of C-mount lens 

Depending on the lens you use, the performance of the camera may not be brought out fully due to 
the  deterioration  in  resolution  and  brightness  in  the  peripheral  area,  occurrence  of  a  ghost, 
aberration and others. When you check the combination between the lens and camera, be sure to 
use the lens you actually use. 
When installing a lens in the camera, make sure carefully that it is not tilted. 
In addition, use a mounting screw free from defects and dirt. Otherwise, the camera may be unable 
to be removed. 
As for the C-mount lens used combining this product, the projection distance from bottom of the 
screw should use 10mm or less.

 

10mm or less

C-mount lens

Bottom of

the screw

 

 

Mounting to a pedestal 

When mounting this product to a pedestal, make sure carefully that the lens doesn't touch with the 
pedestal. 

 

Do not expose the camera’s image-pickup-plane to sunlight or other intense light directly. 

Its inner CMOS sensor might be damaged. 

 

Occurrence of moiré 

If  you  shoot  thin  stripe  patterns,  moiré  patterns  (interference  fringes)  may  appear.  This  is  not  a 
malfunction. 

 

Occurrence of noise on the screen 

If an intense magnetic or electromagnetic field is generated near the camera or connection cable, 
noise may be generated on the screen. If this occurs, move the camera or the cable. 

Summary of Contents for BU SERIES



































Reviews: