background image

 

E-1 

 

 

TOSHIBA Barcode Printer 

B-FV4D SERIES

 

 

Quick Installation Manual 

 
 
Important Information to the User 

In order to meet Product Safety, FCC and CE marking requirements, it is 
advised to use the power cord which was shipped with this product. Otherwise 
this cable needs to meet the following standards. 
 

Power Cord 

For this product a UL listed, detachable power cord is required. Outside the US, 
power cords need to meet the particular country’s certification and application 
requirements. If a different power cord is used from that described above you 
might violate safety certifications which are in force in the country of use.  The 
socket-outlet needs to be installed near the equipment and must be easily 
accessible. 
Pull out the plug from the outlet more than once a year to clean around the 
prongs. Accumulating dust and dirt could cause a fire due to the heat released 
by electric leakage. 
 
 
 
 
 
 
 
 
 

 
 

NOTES: 

1.  This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC 

CORPORATION. 

2.  The contents of this manual may be changed without notification. 
3.  Please refer to your local Authorized Service representative with regard to any queries you may have in 

this manual. 

4.  Centronics is a registered trademark of Centronics Data Computer Corp.

 

E-2 

1.   Unpacking 

Unpack the printer. 

 

1.1  Accessories 

When unpacking the printer, please make sure all the following accessories are supplied with the 
printer. 
 

CD-ROM (1 copy) 

 

Power Adapter (1 pc.) 

Quick Installation Manual 

(1 copy) 

 
 
 

 

 
 
 

 

 

 

 

Safety Precautions (1 copy) 

 

USB Cable (1 pc.) 

 

 

 
 
 

 

 
 

 

 
 
 

 

NOTES:

1.  Check for damages or scratches on the printer.  However, please note that TOSHIBA TEC 

CORPORATION shall have no liability for any damage of any kind sustained during transportation of the 
product. 

2.  Keep the carton and internal packaging for future transportation of the printer.

Summary of Contents for B-FV4D SERIES








Reviews: