Toshiba B-EX6T Series Key Operation Specification Download

Page: 132 / 160

131

9.10.3.4 WRITE RETRY

The number of times tag write is retried and the timeout for write retry are set.
(1) The number of times tag write is retried

Max.

value

Min. value

Step

Display

Sign

Integer

digit

Decimal

place

0-padding

Unit of

measure

255

Decimal

None

Times

The printer retries to write data onto an RFID tag for up to the specified number of times. If the data write

period expired before the specified number of retries, the printer stops the retries at the time.

(2) The timeout for RFID tag write retry

Max.

value

Min. value

Step

Display

Sign

Integer

digit

Decimal

place

0-padding

Unit of

measure

9.9

0.0

0.1

Decimal

None

Second

The printer retries to write data on an RFID tag for the specified length of time.

If the printer has retried for the specified number of times within the RFID write retry timeout, the printer

stops the retries at the time.

9.10.4 UHF SETTING

The parameters related to UHF setting are set.

The menu structure of UHF SETTING

Menu item

<7>RFID

UHF SETTING

POWER LEVEL

Q VALUE

AGC THRESHOLD

WRITE AGC THRESHOLD

WRITE RETRY MIN AGC

CALIB. MODE

CALIB. AGC

CALIB. POSITION

ANTENNA POSITION

9.10.4.1 POWER LEVEL

Radio output level of UHF is set.

Max.

value

Min. value

Step

Display

Sign

Integer

digit

Decimal

place

0-padding

Unit of

measure

See Note 1.

Decimal

None

Notes:

B-EX6T1/T3

1. The maximum and minimum values vary depending on the module type.

Max. value

Min. value

Initial value

B-EX706-RFID-U4-R

B-EX706-RFID-U4-EU/US/AU-R

2. The range of output level is 18 (approx. 100mW) to 0 (approx. 1mW).

Summary of Contents for B-EX6T Series

































































































































































Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands

Toshiba B-EX6T Series, Key Operation Specification

Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands