Toshiba 6410A - CCTV Camera Instruction Manual Download Page 7

Page: 7 / 16

- 7 -

CONNECTIONS AND OPERATIONS

• Power plugs of connected equipment must be disconnected before camera

installation.

• A 75-ohm coaxial cable with connector (3C-2V or 5C-2V) is required for standard

connection.

• For details of wiring and operation of equipment to be connected, refer to their

operation manuals.

• Lens, power supply with cable, connectors and coaxial cable are not supplied with

the camera.

Notes on connecting

5-1. Basic connection Single system configuration

The recommended power supplies for this camera are 6 watt minimum for each 24V
AC UL Listed Class 2 power supply or 12V DC power supply.

Do not overload power supply

CAUTION: Never input 24V AC and 12V DC at the same time.

(

) Recommend power cord is twisted pair line

with a minimum wire size of 18 AWG.

CAMERA

MONITOR TV

24V AC UL Listed Class 2 power supply

12V DC power supply

120V AC

01_p2-p32

06.8.7, 11:08 AM

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for 6410A - CCTV Camera

















Search results

Summary of Contents for 6410A - CCTV Camera

Reviews:

Related manuals for 6410A - CCTV Camera

Brands by name

Popular brands

Toshiba 6410A - CCTV Camera, Instruction Manual

Search results

Summary of Contents for 6410A - CCTV Camera

Reviews:

Related manuals for 6410A - CCTV Camera

Brands by name

Popular brands