Toshiba 55L7400U User Manual Download Page 82

Page: 82 / 184

Basic features

HDMI

CEC Player Control menu functions

Press the

QUICK

button to open the Quick menu.

Select

HDMI CEC Device Control

, and then press the

button.

Press the

(arrow) buttons to select the item you want to

control, and then press the

button.

Item:

Description:

Power

Turns the selected device On and Off

Root Menu

Accesses the selected device’s top menu

Contents Menu

Accesses the content list when the

button is pressed

Setup Menu

Accesses the device’s setup menu

Audio

Selects the device’s sound

Eject

Ejects the device’s media

NOTE

These functions depend on the connected devices.

The HDMI

CEC Device Control item is not available under the following

conditions:

❖

A non-HDMI

input is selected

❖

The

Enable HDMI CEC Control

item is set to

Off

❖

The connected HDMI

CEC device is not a playback, recording or

tuner device

HDMI

CEC Control input source selection

If an HDMI

CEC device with HDMI

switching capability (e.g. an

amplifier) is connected to the HDMI

input, you can select another

HDMI

CEC device that is connected to the master HDMI

device.

Use the

INPUT

button on the remote control or the control panel, see

“Learning about the remote control” on page 47

Using HDMI

CEC Control

Summary of Contents for 55L7400U

























































































































































































Search results

Summary of Contents for 55L7400U

Reviews:

Related manuals for 55L7400U

Brands by name

Popular brands

Toshiba 55L7400U, User Manual

Search results

Summary of Contents for 55L7400U

Reviews:

Related manuals for 55L7400U

Brands by name

Popular brands