Toshiba 55L7400U User Manual Download Page 22

Page: 22 / 184

Introduction

TV front and side panel controls and connections

2 USB ports

1 Digital Audio jack

3 HDMI

ports

ARC HDMI

only port

Power LED

Remote sensor

Ambient light sensor

(Sample Illustration) L7400U Series front and side panel controls and

connections

Front panel

Power On/Standby LED

—Power indicator light, (glows green

when the TV power is On).

Ambient light sensor

—This sensor detects the ambient light

conditions to optimize the backlighting levels, see

“Ambient Light

Sensor” on page 103

Remote Sensor

—Point the remote control toward this remote

sensor, see

“Remote control effective range” on page 46

Left side

3 HDMI

Ports

—High-Definition Multimedia Interface input

receives digital audio and uncompressed digital video from an

HDMI

device. HDMI

connection is necessary to receive 1080p

signals.

ARC HDMI

only port

—Audio Return Channel (ARC) enables

the audio signal of the TV to be sent to an AV amplifier via the

HDMI cable.

Digital Audio Jack

—Optical audio output in Dolby

Digital, DTS

or PCM (pulse-code modulation) format for connecting an external

Dolby

Digital and/or DTS

decoder, amplifier, A/V receiver, or

home theater system with optical audio input.

2 USB Ports

—Used to access video, music, or photo files with

USB device.

TV front and side panel controls and connections

Summary of Contents for 55L7400U

























































































































































































Search results

Summary of Contents for 55L7400U

Reviews:

Related manuals for 55L7400U

Brands by name

Popular brands

Toshiba 55L7400U, User Manual

Search results

Summary of Contents for 55L7400U

Reviews:

Related manuals for 55L7400U

Brands by name

Popular brands