background image

 

1

5-3 Color Temperature Adjustment 

 

(1)  Set the signal generator to RGB, 1024*768, 60HZ(ASTRO-859: PG1 856), Level:178 (70%). 

  Full white pattern. 

(2)    Press up or down key of remote control to select “Cool”, Press  ENTER   key to enter the item. 

R, G, B drive values are set for COOL, Medium, and WARM independently.

 

Color Cool Medium Warm

 

x 0.262 

0.2840 

0.313

 

y 0.262 

0.297 

0.329

 

Adjust 

Tolerance

 

±0.003 ±0.003 ±0.003

 

 

(3)  Select  Cool  

 (1)  Cool spec.: 

  : x = 0.262   

y = 0.262 

  (2) If the x and y value are larger than specification, 

Decrease Red drive from default value. 

Increase Blue drive from default value. 

(3)    If the x or y or both x and y value is/are smaller than specification. 

Increase Red drive from default value 

Decrease Blue drive from default value 

(4) According to a x and y value, please following adjustment of (4-1) or (4-2).

 

        (4-1) If x value is higher than spec 

Decrase Red drive from default value. 

        (4-2) If y value is higher than spec, 

Increase Blue drive from default value 

(4)  Select [Medium] 

    Medium spec.: 

  : x = 0.2840   

y = 0.297 

        Adjust R drive (RED) or B drive (BLUE) to set x and y above. 

(5)  Select [WARM] 

  

WARM spec.: 

  : x = 0.313   

y = 0.329 

Adjust R drive (RED) or B drive (BLUE) to set x and y above. 

 

(6)  Exit Factory Mode: 

After finish adjusting color temperature,press [

EXIT

] to exit factory mode. 

 

 

 

Summary of Contents for 40L2546

























Reviews: