Toro TimeCutter SWX 5050 Operator'S Manual Download Page 3

Page: 3 / 52

Figure 2

Safety alert symbol.

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

Contents

Safety ........................................................................... 4

Safe Operating Practices........................................... 4
Toro Riding Mower Safety ........................................ 6
Slope Indicator ....................................................... 7
Safety and Instructional Decals ................................. 8

Product Overview .........................................................13

Controls ...............................................................13

Operation ....................................................................15

Adding Fuel...........................................................15
Checking the Engine-Oil Level.................................16
Breaking in a New Machine......................................16
Think Safety First ...................................................16
Starting the Engine .................................................18
Operating the Parking Brake (SmartPark

™

) ................18

Maintenance .................................................................26

Recommended Maintenance Schedule(s) ......................26
Premaintenance Procedures ........................................27

Raising the Seat ......................................................27
Raising the Front of the Machine ..............................27

Lubrication ...............................................................27

Greasing the Bearings .............................................27

Engine Maintenance ..................................................28

Servicing the Air Cleaner .........................................28
Servicing the Engine Oil..........................................29
Servicing the Spark Plug ..........................................31
Cleaning the Cooling System ....................................32

Fuel System Maintenance ...........................................32

Replacing the In-Line Fuel Filter...............................32

Electrical System Maintenance ....................................33

Charging the Battery ...............................................33
Servicing the Fuses .................................................35

Drive System Maintenance .........................................35

Checking the Tire Pressure ......................................35
Releasing the Electric Brake .....................................35

Hydraulic System Maintenance ....................................36

Checking the Hydraulic Oil Level..............................36
Changing the Hydraulic System Oil and

Filters................................................................37

Mower Maintenance ...................................................39

Servicing the Cutting Blades.....................................39
Leveling the Mower Deck ........................................41
Removing the Mower..............................................43
Mower Belt Maintenance .........................................43
Installing the Mower ...............................................44
Replacing the Grass Deflector ..................................44

Cleaning ...................................................................46

Cleaning under the Front of the Machine ...................46
Washing the Underside of the Mower Deck ................46

Storage ........................................................................47

Cleaning and Storage ..............................................47

Troubleshooting ...........................................................48
Schematics ...................................................................50

Summary of Contents for TimeCutter SWX 5050





















































Search results

Summary of Contents for TimeCutter SWX 5050

Reviews:

Related manuals for TimeCutter SWX 5050

Brands by name

Popular brands

Toro TimeCutter SWX 5050, Operator'S Manual

Search results

Summary of Contents for TimeCutter SWX 5050

Reviews:

Related manuals for TimeCutter SWX 5050

Brands by name

Popular brands