manualshive.com logo in svg

Toro TimeCutter 74750, Operator'S Manual

Share
Download
Toro TimeCutter 74750 Operator'S Manual Download Page 31

B

A

C

D

E

F

g027484

Figure 34

Servicing the Spark Plug

Service Interval:

Every 50 hours—Check the spark plug.

Every 100 hours—Replace the spark plug.

Ensure that the air gap between the center and side electrodes
is correct before installing the spark plug. Use a spark plug
wrench for removing and installing the spark plug and a
gapping tool or feeler gauge to check and adjust the air gap.
Install a new spark plug if necessary.

Type:

Champion

®

RC12YC, Autolite

®

3924, or NGK

®

BCPR6ES

Air Gap:

0.76 mm (0.03 inch)

Removing the Spark Plug

1.

Disengage the blade-control switch, move the motion
controls outward to the P

ARK

position, shut off the

engine, and remove the key.

2.

Before removing the spark plug(s), clean the area
around the base of the plug to keep dirt and debris out
of the engine.

3.

Remove the spark plug (

Figure 35

).

B

A

g027478

Figure 35

Checking the Spark Plug

Important:

Do not clean the spark plug(s). Always

replace the spark plug(s) when it has: a black coating,
worn electrodes, an oily film, or cracks.

Note:

If you see light brown or gray on the insulator, the

engine is operating properly. A black coating on the insulator
usually means the air cleaner is dirty.

Set the gap to 0.76 mm (0.030 inch).

B

A

g027479

Figure 36

Installing the Spark Plug

Tighten the spark plug to 20 N•m (15 ft-lb).

Figure 37

31

 

Summary of Contents for TimeCutter 74750

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands