background image

Seat Adjustment (Fig. 6) The seat adjusting lever allows 15 cm
(5.9 inches) fore and aft adjustment in 15 mm increments.

Arm Rest (Fig. 7) The arm rest pivots up and down.  

Backrest Knob (Fig. 7)—The backrest knob adjusts the back-
rest angle from 5–20 degrees.

Suspension Lever (Fig. 7). The suspension lever adjusts the
seat to the operator’s weight.  Use the up position for light-
weight operators, the down position for heavy-weight operators.
The backrest cushion and bottom seat cushion are removable.

Warning Light Test Button (Fig. 8)—Before operating, press
the test button.  All lights on the steering tower should illumi-
nate.  Any light that does not come on indicates an electrical
malfunction that should be repaired immediately.  The oil pres-
sure and no-charge indicator lights illuminate when turning the
key switch “ON”.

Hydraulic and Engine Indicator Lights (Fig. 8)—If these
lights come on, stop the machine and make repairs immediately.

Engine Oil Pressure Warning (Fig. 8)—Dangerously low
engine oil pressure is indicated by both a warning indicator
light and an audible signal.  When this occurs, stop the engine
immediately and correct the problem.

Fuel System Warning (Fig. 8)—A warning indicator light and
audible signal warn of excess water in the fuel system.

Coolant Temperature Warning (Fig. 8)—If the engine coolant
temperature exceeds 203° F (95° C) a warning indicator light
illuminates and audible signal sounds.  The engine shuts down
if the coolant’s temperature exceeds 230° F (110° C).  The
switch resets automatically when system and engine cool down.

No Charge Warning (Fig. 8)—No charge to the batteries is
indicated by a warning indicator light and audible signal.

Hydraulic Oil Temperature Warning (Fig. 8)—A warning

Figure 6

1.

Seat Adjusting Lever

Figure 7

1.

Arm Rest

2.

Backrest knob

3.

Suspension Lever

To make sure the interlock switch operates correctly,
the seat suspension must be set for the weight of each
operator.  If the suspension is not set correctly, the
engine will run intermittently and tend to stall.  To
correct this, set the suspension lighter.

CAUTION

Controls

Summary of Contents for REELMASTER 4500-D





























Reviews: